Located on the back, screws 7 through 11 are used for starting weld schedules.
The system detects and outputs trouble signals (such as "No-Weld Error 07") if power supply or contact connections are inverted.
Time the pressure is maintained after the current stops.
For detailed diagrams and specific wiring instructions, you can refer to the official CY-210B User's Manual Addendum provided by Amada Weld Tech or help troubleshooting a particular error code on your CY-210B?
End of Manual
Attach the remaining active wire from your single-level foot switch directly into . 2. Advanced Multi-Stage and Forge Weld Switching
A: The controller can store up to .
Examines each half-cycle of actual weld current and compensates for fluctuations to ensure consistent results.
Always refer to the original CY-210B User's Manual (Addendum C/Rev C) for precise installation. 2. Installation and Setup Instructions (CY-210B Manual)
Ensure the start signal is correctly applied; some modes prevent sequence execution if signals are fed improperly.
To reset these counters, navigate to the counter menu and press and hold MODE for three seconds. External reset signals can also be used if configured.
To help you find the right page, are you troubleshooting a or looking for wiring diagrams for the terminal block?
Maintains secondary current stability through a toroidal coil.
Setting the OFF time to 00 enables single operation; 01-99 cycles allows for continuous welding.
Cookie-Einstellungen
Wir verwenden Cookies, um unsere Webseiten für Sie optimal zu gestalten, Funktionen wie Videowiedergabe anbieten zu können und die Zugriffe auf unsere Website zu analysieren. Wir geben keine personenbezogenen Daten an Dritte weiter. Wenn Sie auf "Alle akzeptieren" klicken, stimmen Sie der Anwendung von Cookies zu. Weitere Informationen finden Sie unter Datenschutz.
Cookie-Einstellungen anpassen
Es werden verschiedene Kategorien von Cookies unterschieden. Einige von ihnen sind unbedingt erforderlich, andere werden für bestimmte Funktionen benötigt oder helfen, das BayernPortal zu verbessern. Nachfolgend finden Sie Informationen über die Cookies je Kategorie.
Unbedingt erforderliche Cookies
Located on the back, screws 7 through 11 are used for starting weld schedules.
The system detects and outputs trouble signals (such as "No-Weld Error 07") if power supply or contact connections are inverted.
For detailed diagrams and specific wiring instructions, you can refer to the official CY-210B User's Manual Addendum provided by Amada Weld Tech or help troubleshooting a particular error code on your CY-210B?
End of Manual
Attach the remaining active wire from your single-level foot switch directly into . 2. Advanced Multi-Stage and Forge Weld Switching Located on the back, screws 7 through 11
A: The controller can store up to .
Examines each half-cycle of actual weld current and compensates for fluctuations to ensure consistent results.
Ensure the start signal is correctly applied; some modes prevent sequence execution if signals are fed improperly.
To reset these counters, navigate to the counter menu and press and hold MODE for three seconds. External reset signals can also be used if configured.
To help you find the right page, are you troubleshooting a or looking for wiring diagrams for the terminal block?
Maintains secondary current stability through a toroidal coil.
Setting the OFF time to 00 enables single operation; 01-99 cycles allows for continuous welding.
Cookies zur Auswertung des Nutzerverhaltens
Diese Cookies halten Ihre Besuche im BayernPortal fest (z. B. wie schnell eine Seite geladen wird, wie Sie auf der Seite navigieren). Sie werden benötigt, um zu ermitteln, an welchen Stellen das BayernPortal und die Inhalte verbessert werden können. Es wird das Webanalyse-Tool Matomo Analytics eingesetzt.
Name
trackingConsent
Gültigkeitsdauer
1 Jahr(e)
Beschreibung
Dieses Cookie speichert Ihre Zustimmung zur Auswertung Ihres Besuchs.
Name
_pk_id.*
Gültigkeitsdauer
1 Stunde(n)
Beschreibung
Dieses Cookie speichert eine eindeutige User-ID, die die Auswertung Ihres Nutzerverhaltens innerhalb einer Stunde ermöglicht.
Name
_pk_ses.*
Gültigkeitsdauer
Ende der Browsersitzung
Beschreibung
Dieses Cookie speichert eine eindeutige User-ID für die Auswertung Ihres Nutzerverhaltens während Ihres Besuchs.
Cookies für Komfortfunktionen
Für bestimmte Komfortfunktionen werden Cookies benötigt (z. B. für die Wiedergabe von Videos).
Name
comfortConsent
Gültigkeitsdauer
1 Jahr(e)
Beschreibung
Dieses Cookie speichert Ihre Zustimmung zum Setzen von Cookies für Komfortfunktionalitäten des BayernPortals (wie z. B. für die Wiedergabe von Videos).
Name
videoConsent
Gültigkeitsdauer
1 Jahr(e)
Beschreibung
Dieses Cookie speichert Ihre Zustimmung zur Wiedergabe von Videos im BayernPortal. Sie müssen dann nicht bei jedem Video zustimmen.